18 Years Factory Small Electric Hydraulic Power Units/Packs - high quality hydraulic unit 220v hydraulic power unit for hydraulic lifting – Guorui
18 Years Factory Small Electric Hydraulic Power Units/Packs - high quality hydraulic unit 220v hydraulic power unit for hydraulic lifting – Guorui Detail:
GENERAL INFORMATION
Product Presentation：
LOW NOISE：The noise value is very low, the structure of the internal gear pump, and the special tooth shape is used to make the meshing
volume become very small.
LOW PULSATION：Pulsation is almost non-existent (2kgf/cm2), so systems with sophisticated speed control requirements like machining machines are
most suitable for use.
LONG SERVICE LIFE：lt adopts two-stage pressure rise, with working pressure up to 25MPa and maximum-pressure up to 32Mpa
HIGH PRESSURE RESISTANCE：The pressure generated during the opeation of the oil pump makes the slidingelements forcibly lubricated, with little wear and
improves the service life of the pump
GRH specializes in offering hydraulic components and technology solutions for hydraulic years for more than 30 years, with our establishment way back in 1986.
Our product catalogue is extensive, with our primary products including hydraulic gear pumps and pump valve assemblies, hydraulic power units, proportional valves, monoblock directional control valves, cycloidal speed reducers, hydraulic gear motors and geared flow dividers. We also offer a full line of hydraulic technology and system solutions, connecting our experience with expert staff, ensuring we are able to fully meet an array of customer requirements, with the hydraulic components widely used in industrial machinery, lifting machinery, construction machinery, agricultural equipment and other industrial applications.
Cycloidal gear motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Cycloidal gear motors operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits the torque generated by the application of pressure from hydraulic oil fed into moto which is then delivered via the motor’s output shaft. Cycloidal gear motors have high starting torque and constant output torque at wide speed range.
DISTIBUTORVALVE
GR, GRS series motors have spool valve: the distributor valve has been integrated with the output shaft. The cardan shaft rotates distributor valve and transfers mechanical energy from gerotor set to output shaft. The valve has hydrodynamic bearings and has infinite life when load ratings are not exceeded.
GEAR WHEEL SET
There are two forms of gearwheel set:
Roll-gerotor set has teeth fitted with rollers. The rollers reduce local stress and the tangential reaction forces on the rotor reducing friction to a minimum. This gives long operating life and better efficiency even at continuous high pressures.
Roll-gerotor sets are recommended for operation with thin oil and for applications with continually reversing applications with continually reversing loads. GR, GRS series motors have roll-gerotor set.
APPLICATION
» Conveyors
» Feeding mechanism of robots and manipulators
» Metal working machines
» Textile machines
» Agricultural machines
» Food industries
» Grass cutting machinery etc.
OPTIONS
» Model-Spool valve, roll-gerotor
» Flange mount
» Motor with needle bearing
» Side and rear ports
» Shafts: straight, splined and tapered
» Shaft seal for high and low pressure
» Metric and BSPP ports
» Speed sensoring
» Other special features
GENERAL
| Max.Displacement | cm3/rev | 397 | ||
| Max.Speed | RPM | 970 | ||
| Max.Torque | Nm |
cont.:610 |
int.:690 | |
| Max.Output | KW | 15 | ||
| Max.Pressure Drop | Mpa |
cont.:17.5 |
int.:20 | |
| Max.Oil Flow | lpm | 75 | ||
| Min.Speed | RPM | 10 | ||
| Pressure Fluid | Mineral based-HLP(DIN 51524) or HM(ISO 6743/4) | |||
| Temperature Range | -40 to 140 | |||
| Optimal Viscosity Range | mm2/s | 20 to 75 | ||
| Filtration | ISO code 20/16 (Min.) (recommended fluid filtration of 25 microns) ISO 20/16 | |||
Specification data for GR series motor
| Displacement(cm3/rev) |
GR 50 |
GR 80 |
GR 100 |
GR 125 |
GR 160 |
GR 200 |
GR 250 |
GR 315 |
GR 400 |
|
|
51,5 |
80,3 |
99,8 |
125,7 |
159,6 |
199,8 |
250,1 |
315,7 |
397 |
||
| Max Speed | Cont. |
775 |
750 |
600 |
475 |
375 |
300 |
240 |
190 | 0 |
|
Int.* |
970 |
940 |
750 |
600 |
470 |
375 |
300 |
240 |
190 |
|
| Max Torque | Cont. |
100 |
200 |
240 |
300 |
390 |
385 |
390 |
360 |
380 |
| Nm | Int.* |
130 |
220 |
280 |
340 |
430 |
460 |
470 |
470 |
470 |
| Peak** |
170 |
270 |
320 |
370 |
460 |
560 |
600 |
610 |
610 |
|
| Max Output | Cont. |
7 |
12,5 |
13 |
12,5 |
11,5 |
9 |
8 |
5 |
4,8 |
|
Int.* |
8,5 |
15 |
15 |
14,5 |
14 |
12 |
9,5 |
8 |
6,8 |
|
| Max Pressure Drop | Cont. |
14 |
17,5 |
17,5 |
17,5 |
17,5 |
14 |
11 |
8,5 |
6,5 |
| Mpa | Int.* |
17,5 |
20 |
20 |
20 |
20 |
17,5 |
14 |
11,5 |
9 |
| Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
20 |
15 |
11,5 |
|
| Max Oil Flow | Cont. |
40 |
60 |
60 |
60 |
60 |
60 |
60 |
60 |
60 |
|
Int.* |
50 |
75 |
75 |
75 |
75 |
75 |
75 |
75 |
75 |
|
| Max Inlet Pressure | Cont. |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
| Int.* |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
|
| Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
|
| Max.Return Pressure with Drain Line | Cont. |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
| Int.* |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
|
| Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
|
| Max.Starting Pressure with Unloaded Shaft |
1 |
1 |
1 |
0,9 |
0,7 |
0,5 |
0,4 |
0,3 |
0,3 |
|
| Min Starting Torque | At max.press. drop Cont. |
80 |
150 |
200 |
250 |
320 |
330 |
310 |
315 |
315 |
|
At max.press.drop Int.* |
100 |
170 |
230 |
280 |
370 |
400 |
480 |
580 |
500 |
|
| Min.Speed |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
|
| Weight(kg) | MR(F) |
6,8 |
6,9 |
7,2 |
7,3 |
7,5 |
8 |
8,4 |
9,1 |
9,8 |
|
MRQ(N) |
6,2 |
6,3 |
6,6 |
6,8 |
7,6 |
7,2 |
7,8 |
8,6 |
9,3 |
|
Product detail pictures:
Related Product Guide:
Coal Mining Machines Market 2018- Global Industry Analysis, By Key Players, Segmentation, Trends And Forecast By 2023 | Yuken Hydraulic Valve
World Highways | Monoblock Control Valve On Tractor
We usually think and practice corresponding for the change of circumstance, and grow up. We aim at the achievement of a richer mind and body as well as the living for 18 Years Factory Small Electric Hydraulic Power Units/Packs - high quality hydraulic unit 220v hydraulic power unit for hydraulic lifting – Guorui, The product will supply to all over the world, such as: Munich, Tunisia, Nepal, As an experienced factory we also accept customized order and make it same as your picture or sample specifying specification and customer design packing. The main goal of the company is to live a satisfactory memory to all the customers, and establish a long term win-win business relationship. For more information, please contact us. And It is our great pleasure if you like to have a personally meeting in our office.
By Emily from Slovak Republic - 2016.01.28 19:59
The factory technical staff gave us a lot of good advice in the cooperation process, this is very good, we are very grateful.
By Elma from Costa rica - 2015.09.29 17:23
