OEM Factory for Machines Use Hydraulic Systems - GRS series – Guorui
OEM Factory for Machines Use Hydraulic Systems - GRS series – Guorui Detail:
GENERAL INFORMATION
Cycloidal gear motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Cycloidal gear motors operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits the torque generated by the application of pressure from hydraulic oil fed into moto which is then delivered via the motor’s output shaft. Cycloidal gear motors have high starting torque and constant output torque at wide speed range.
DISTIBUTORVALVE
GR, GRS series motors have spool valve: the distributor valve has been integrated with the output shaft. The cardan shaft rotates distributor valve and transfers mechanical energy from gerotor set to output shaft. The valve has hydrodynamic bearings and has infinite life when load ratings are not exceeded.
GEAR WHEEL SET
There are two forms of gearwheel set:
Roll-gerotor set has teeth fitted with rollers. The rollers reduce local stress and the tangential reaction forces on the rotor reducing friction to a minimum. This gives long operating life and better efficiency even at continuous high pressures.
Roll-gerotor sets are recommended for operation with thin oil and for applications with continually reversing applications with continually reversing loads. GR, GRS series motors have roll-gerotor set.
APPLICATION
» Conveyors
» Feeding mechanism of robots and manipulators
» Metal working machines
» Textile machines
» Agricultural machines
» Food industries
» Grass cutting machinery etc.
OPTIONS
» Model-Spool valve, roll-gerotor
» Flange mount
» Motor with needle bearing
» Side and rear ports
» Shafts: straight, splined and tapered
» Shaft seal for high and low pressure
» Metric and BSPP ports
» Speed sensoring
» Other special features
GENERAL
Max.Displacement | cm3/rev | 397 | ||
Max.Speed | RPM | 970 | ||
Max.Torque | Nm |
cont.:610 |
int.:690 | |
Max.Output | KW | 15 | ||
Max.Pressure Drop | Mpa |
cont.:17.5 |
int.:20 | |
Max.Oil Flow | lpm | 75 | ||
Min.Speed | RPM | 10 | ||
Pressure Fluid | Mineral based-HLP(DIN 51524) or HM(ISO 6743/4) | |||
Temperature Range | -40 to 140 | |||
Optimal Viscosity Range | mm2/s | 20 to 75 | ||
Filtration | ISO code 20/16 (Min.) (recommended fluid filtration of 25 microns) ISO 20/16 |
Specification data for GR series motor
Displacement(cm3/rev) |
GR 50 |
GR 80 |
GR 100 |
GR 125 |
GR 160 |
GR 200 |
GR 250 |
GR 315 |
GR 400 |
|
51,5 |
80,3 |
99,8 |
125,7 |
159,6 |
199,8 |
250,1 |
315,7 |
397 |
||
Max Speed | Cont. |
775 |
750 |
600 |
475 |
375 |
300 |
240 |
190 | 0 |
Int.* |
970 |
940 |
750 |
600 |
470 |
375 |
300 |
240 |
190 |
|
Max Torque | Cont. |
100 |
200 |
240 |
300 |
390 |
385 |
390 |
360 |
380 |
Nm | Int.* |
130 |
220 |
280 |
340 |
430 |
460 |
470 |
470 |
470 |
Peak** |
170 |
270 |
320 |
370 |
460 |
560 |
600 |
610 |
610 |
|
Max Output | Cont. |
7 |
12,5 |
13 |
12,5 |
11,5 |
9 |
8 |
5 |
4,8 |
Int.* |
8,5 |
15 |
15 |
14,5 |
14 |
12 |
9,5 |
8 |
6,8 |
|
Max Pressure Drop | Cont. |
14 |
17,5 |
17,5 |
17,5 |
17,5 |
14 |
11 |
8,5 |
6,5 |
Mpa | Int.* |
17,5 |
20 |
20 |
20 |
20 |
17,5 |
14 |
11,5 |
9 |
Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
20 |
15 |
11,5 |
|
Max Oil Flow | Cont. |
40 |
60 |
60 |
60 |
60 |
60 |
60 |
60 |
60 |
Int.* |
50 |
75 |
75 |
75 |
75 |
75 |
75 |
75 |
75 |
|
Max Inlet Pressure | Cont. |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
Int.* |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
|
Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
|
Max.Return Pressure with Drain Line | Cont. |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
Int.* |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
|
Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
|
Max.Starting Pressure with Unloaded Shaft |
1 |
1 |
1 |
0,9 |
0,7 |
0,5 |
0,4 |
0,3 |
0,3 |
|
Min Starting Torque | At max.press. drop Cont. |
80 |
150 |
200 |
250 |
320 |
330 |
310 |
315 |
315 |
At max.press.drop Int.* |
100 |
170 |
230 |
280 |
370 |
400 |
480 |
580 |
500 |
|
Min.Speed |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
|
Weight(kg) | MR(F) |
6,8 |
6,9 |
7,2 |
7,3 |
7,5 |
8 |
8,4 |
9,1 |
9,8 |
MRQ(N) |
6,2 |
6,3 |
6,6 |
6,8 |
7,6 |
7,2 |
7,8 |
8,6 |
9,3 |
Product detail pictures:
Related Product Guide:
Hitachi EX5600-6 Excavator | Yuken Hydraulic Valve
Trials suggest harsh environment subsea trees are feasible | 12v Dc Hydraulic Power Pack With Hand Pump
Fast and good quotations, informed advisers to help you choose the correct product that suits all your needs, a short production time, responsible quality control and different services for paying and shipping affairs for OEM Factory for Machines Use Hydraulic Systems - GRS series – Guorui, The product will supply to all over the world, such as: Porto, Swiss, Georgia, We set a strict quality control system. We have return and exchange policy, and you can exchange within 7 days after receive the wigs if it is in new station and we service repairing free for our products. Please feel free to contact us for further information and we will offer you competitive price list then.
By Ellen from Ukraine - 2016.04.28 15:45
In general, we are satisfied with all aspects, cheap, high-quality, fast delivery and good procuct style, we will have follow-up cooperation!
By Faithe from Japan - 2015.02.08 16:45