factory Outlets for Dc 12v Mini Hydraulic Power Unit/Pack - GRS series – Guorui
factory Outlets for Dc 12v Mini Hydraulic Power Unit/Pack - GRS series – Guorui Detail:
GENERAL INFORMATION
Cycloidal gear motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Cycloidal gear motors operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits the torque generated by the application of pressure from hydraulic oil fed into moto which is then delivered via the motor’s output shaft. Cycloidal gear motors have high starting torque and constant output torque at wide speed range.
DISTIBUTORVALVE
GR, GRS series motors have spool valve: the distributor valve has been integrated with the output shaft. The cardan shaft rotates distributor valve and transfers mechanical energy from gerotor set to output shaft. The valve has hydrodynamic bearings and has infinite life when load ratings are not exceeded.
GEAR WHEEL SET
There are two forms of gearwheel set:
Roll-gerotor set has teeth fitted with rollers. The rollers reduce local stress and the tangential reaction forces on the rotor reducing friction to a minimum. This gives long operating life and better efficiency even at continuous high pressures.
Roll-gerotor sets are recommended for operation with thin oil and for applications with continually reversing applications with continually reversing loads. GR, GRS series motors have roll-gerotor set.
APPLICATION
» Conveyors
» Feeding mechanism of robots and manipulators
» Metal working machines
» Textile machines
» Agricultural machines
» Food industries
» Grass cutting machinery etc.
OPTIONS
» Model-Spool valve, roll-gerotor
» Flange mount
» Motor with needle bearing
» Side and rear ports
» Shafts: straight, splined and tapered
» Shaft seal for high and low pressure
» Metric and BSPP ports
» Speed sensoring
» Other special features
GENERAL
| Max.Displacement | cm3/rev | 397 | ||
| Max.Speed | RPM | 970 | ||
| Max.Torque | Nm |
cont.:610 |
int.:690 | |
| Max.Output | KW | 15 | ||
| Max.Pressure Drop | Mpa |
cont.:17.5 |
int.:20 | |
| Max.Oil Flow | lpm | 75 | ||
| Min.Speed | RPM | 10 | ||
| Pressure Fluid | Mineral based-HLP(DIN 51524) or HM(ISO 6743/4) | |||
| Temperature Range | -40 to 140 | |||
| Optimal Viscosity Range | mm2/s | 20 to 75 | ||
| Filtration | ISO code 20/16 (Min.) (recommended fluid filtration of 25 microns) ISO 20/16 | |||
Specification data for GR series motor
| Displacement(cm3/rev) |
GR 50 |
GR 80 |
GR 100 |
GR 125 |
GR 160 |
GR 200 |
GR 250 |
GR 315 |
GR 400 |
|
|
51,5 |
80,3 |
99,8 |
125,7 |
159,6 |
199,8 |
250,1 |
315,7 |
397 |
||
| Max Speed | Cont. |
775 |
750 |
600 |
475 |
375 |
300 |
240 |
190 | 0 |
|
Int.* |
970 |
940 |
750 |
600 |
470 |
375 |
300 |
240 |
190 |
|
| Max Torque | Cont. |
100 |
200 |
240 |
300 |
390 |
385 |
390 |
360 |
380 |
| Nm | Int.* |
130 |
220 |
280 |
340 |
430 |
460 |
470 |
470 |
470 |
| Peak** |
170 |
270 |
320 |
370 |
460 |
560 |
600 |
610 |
610 |
|
| Max Output | Cont. |
7 |
12,5 |
13 |
12,5 |
11,5 |
9 |
8 |
5 |
4,8 |
|
Int.* |
8,5 |
15 |
15 |
14,5 |
14 |
12 |
9,5 |
8 |
6,8 |
|
| Max Pressure Drop | Cont. |
14 |
17,5 |
17,5 |
17,5 |
17,5 |
14 |
11 |
8,5 |
6,5 |
| Mpa | Int.* |
17,5 |
20 |
20 |
20 |
20 |
17,5 |
14 |
11,5 |
9 |
| Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
20 |
15 |
11,5 |
|
| Max Oil Flow | Cont. |
40 |
60 |
60 |
60 |
60 |
60 |
60 |
60 |
60 |
|
Int.* |
50 |
75 |
75 |
75 |
75 |
75 |
75 |
75 |
75 |
|
| Max Inlet Pressure | Cont. |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
| Int.* |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
|
| Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
|
| Max.Return Pressure with Drain Line | Cont. |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
17,5 |
| Int.* |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
20 |
|
| Peak** |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
22,5 |
|
| Max.Starting Pressure with Unloaded Shaft |
1 |
1 |
1 |
0,9 |
0,7 |
0,5 |
0,4 |
0,3 |
0,3 |
|
| Min Starting Torque | At max.press. drop Cont. |
80 |
150 |
200 |
250 |
320 |
330 |
310 |
315 |
315 |
|
At max.press.drop Int.* |
100 |
170 |
230 |
280 |
370 |
400 |
480 |
580 |
500 |
|
| Min.Speed |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
10 |
|
| Weight(kg) | MR(F) |
6,8 |
6,9 |
7,2 |
7,3 |
7,5 |
8 |
8,4 |
9,1 |
9,8 |
|
MRQ(N) |
6,2 |
6,3 |
6,6 |
6,8 |
7,6 |
7,2 |
7,8 |
8,6 |
9,3 |
|
Product detail pictures:
Related Product Guide:
Caterpillar Introduces 5-Seat Utility Vehicles | Sectional Hydraulic Control Valve
RTU Single and Dual Power Supply with Integrated Backup Battery Charging | Komatsu Hydraulic Gear Pump
Our company puts emphasis on the management, the introduction of talented personnel, and the construction of staff building, trying hard to improve the quality and liability consciousness of staff members. Our company successfully attained IS9001 Certification and European CE Certification of factory Outlets for Dc 12v Mini Hydraulic Power Unit/Pack - GRS series – Guorui, The product will supply to all over the world, such as: Surabaya, Canada, Bolivia, With the effort to keep pace with world's trend, we'll always endeavor to meet customers' demands. If you want develop any other new items, we can customize them to suit your needs. If you feel interest in any of our products and solutions or want develop new merchandise, you should feel free to contact us. We are looking forward to forming successful business relationship with customers all over the world.
By Gail from Czech - 2016.12.31 14:53
The company keeps to the operation concept "scientific management, high quality and efficiency primacy, customer supreme", we have always maintained business cooperation. Work with you,we feel easy!
By Miguel from Bhutan - 2015.11.04 10:32
